Altair Hypercam 183C PRO Color astro camera Peltier cooling Sony sensor D=15.9mm

Altair Hypercam 183C PRO Color astro camera Peltier cooling Sony sensor D=15.9mm


The new Altair Hypercam 183C PRO TEC COOLED color camera is an excellent camera for deep-sky astrophotography
♦ Sensor: SONY Exmor R BSI IMX183 Color CMOS sensor

♦ 5440x3648 pixels - about 20 million pixels

♦ Sensor size: approx. 13x9 mm - diagonal approx. 16 mm

♦ Pixel size 2.4 µm

♦ Extremely sensitive to light thanks to back illumination technology - QE 84%

♦ Peltier cooling up to 45 °C below ambient temperature

♦ 4 GB DDR3 RAM frame buffer for more stable data transmission

♦ Equipped with USB 3.0 interface

♦ With the purchase of this camera you will receive a one-year user license for the program SharpCap PRO

♦ Supplied with a high-quality transport case

Altair Hypercam 183C PRO TEC COOLED Color CMOS astro camera
The SONY Exmor R BSI IMX183 color CMOS sensor was installed in this camera. The chip has a resolution of 5440x3648 pixels, which is almost 20 million pixels. As far as the number of pixels is concerned, the CMOS camera is one of the largest cameras currently available.

The camera can be cooled to a maximum of 45 °C below the ambient temperature. Due to the very low amplifier glow, the camera is ideally suited for astronomical applications. The back illumination technique makes the chip extremely light sensitive. The camera is equipped with a USB3.0+USB2.0 interface.

Suitable software is included in the scope of delivery and can be downloaded from Altair Astro Customer Support.

SharpCap PRO:
With the purchase of this camera you also get a user license for the program SharpCap 3.0 plus software SharpCap PRO (a program with many features especially for astrophotography) limited to 1 year.

Altair Astro has been working closely with SharpCap developer Robin Glover since 2015 to fully integrate the Altair cameras with SharpCap from the ground up. Now, Sharpcap PRO enables even more features with this camera, such as software-assisted polar alignment (more accurate than most other methods), live flat subtraction, and live dark frame subtraction. The fast, accurate polar alignment feature in SharpCap PRO is a lifesaver for photography, saving set-up time.

Important: Windows PC hardware requirements for best performance

♦ Minimum CPU: Equal to i5 or higher
♦ Minimum memory: 8 GB or more
♦ USB port: USB2.0 high speed port or USB3.0 high speed port (best performance)
♦ Please note: some laptops and touchscreen notebooks may not have sufficient USB throughput.

Peltier cooling:
Cooling reduces thermal noise during a long exposure. The internal thermoelectric cooling system can be controlled with the recording program, so you can select a working temperature (stored in the .FITs header). The Hypercam is designed for consistent deep-sky recordings up to 45 °C below the ambient temperature, the appropriate temperature of the IMX183 sensor at Gain 400 is -10/15 °C absolute, below which no further improvements are to be expected.

Optical window with heating against fogging. Every precaution has been taken regarding the biggest problem of cooled cameras. The optical window is heated by special heaters to prevent fogging at low temperatures. To prevent frost from forming on the sensor, the sensor chamber is sealed and filled with dry air during manufacture. Inside the chamber is a stainless steel desiccant cartridge which can be regenerated by placing it in an oven at 120°C for a few hours after removing the small O-ring.
Sensor: SONY Exmor R BSI IMX183 Color CMOS sensor
Sensor size: 13mm x 9mm / diagonal 16mm
Vertical resolution: 3648px
Horizontal resolution: 5440px
Pixel count: 20 million
Pixel size: 2.4µm x 2.4µm
Bit rate: 8/12 bits
Data transfer: USB3.0 (USB.0 possible)
Cooling: 45°C below ambient
Power supply cooling: 12 V
Power supply camera: USB
Autoguiding connection: ST4
Max. exposure time: 1000 sec
Case diameter: 65mm
Connection to the telescope: T2, 2"
USB Hub: Two USB2.0 sockets on the back
Distance T2 thread to sensor: 12.5 mm

♦ Camera with 4 GB DDR3 RAM, cooling system and T2 connection
♦ 12 V power pack for cooling
♦ 1.8m USB3.0 connection cable
♦ 2" plug-in connection with filter thread
♦ UV-IR cut filter
♦ Cover caps
♦ High-quality transport case
♦ Desiccant cartridge
♦ Software available for download from the manufacturer (altaircameras.com)